Month: August 2020

Name is Bis(acetylacetone)copper, as a common heterocyclic compound, it belongs to copper-catalyst compound, and cas is 13395-16-9, its synthesis route is as follows.,13395-16-9

General procedure: In a typical synthesis of Cu40Ag60, 0.45mmol Cu(acac)2 and 0.35 Ag (ac) was mixed with 3mL of OAm, 1 mL of OAc and 11mL of ODE. All synthesis was conducted in a four-necked glass reactor allowing the precise temperature control and inert gas atmosphere under dark conditions. Firstly, the mixture was heated to 60C and kept at this temperature for 10min. Then, the mixture was heated to 180C and kept at this temperature for 30min before it was cooled down to room temperature. After cooling, the resultant reaction mixture was collected with hexane (2mL) and the NPs were separated by centrifugation (8500rpm, 12min) after adding isopropanol (40mL). To further purify the yielded CuAg NPs, the product was centrifuged (8500rpm, 12min) one more time with ethanol (40mL). Finally, the remaining product was dispersed in hexane (10mL) for further use. By using the same recipe and varying metal precursor amounts, two different compositions of CuAg NPs were synthesized. Reductive mixing of 0.3mmol Cu(acac)2 and 0.5 Ag(ac) resulted in Cu30Ag70 NPs and mixing 0.6mmol Cu(acac)2 with 0.4 Ag (ac) led to Cu60Ag40. Synthesis of Ag NPs was conducted with the same recipe without using Cu precursor.

With the complex challenges of chemical substances, we look forward to future research findings about Bis(acetylacetone)copper

Reference£º
Article; Balkan, Timucin; Kuecuekkececi, Hueseyin; Kaya, Sarp; Metin, Oender; Zarenezhad, Hamaneh; Journal of Alloys and Compounds; vol. 831; (2020);,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

Name is Bis(acetylacetone)copper, as a common heterocyclic compound, it belongs to copper-catalyst compound, and cas is 13395-16-9, its synthesis route is as follows.,13395-16-9

Cu(C5H7O2)2 (13.1 mg, 0.05 mmol) was solubilized in 5 mL of methanoland added to a 5 mL of methanolic solution of HL (24.0 mg,0.1 mmol). The mixture was stirred under reflux for 1 h. Dark greencrystals suitable for X-ray diffraction analysis were obtained after somedays from the mother liquor at room temperature. Yield: 22.9 mg(84.5%). Melting point: Decomposes after 260 C. Molar conductivity(1 mM, DMF): 0.35 Omega-1¡¤cm2¡¤mol-1 Elemental analysis calculated forC26H22O2N8Cu (%): C. 57.61; H. 4.09; N. 20.67. Found (%): C. 57.65; H.3.83; N. 20.64. IR bands (KBr, cm-1): nu(CeO) 1371; nu(C]N) 1580,1557; nu(NeN) 1160; rho(py) 735. ESI-MS [C26H23O2N8Cu]+ calcd./found(m/z)=542.1240, 542.1251.

With the complex challenges of chemical substances, we look forward to future research findings about Bis(acetylacetone)copper

Reference£º
Article; Santiago, Pedro H.O.; Santiago, Mariana B.; Martins, Carlos H.G.; Gatto, Claudia C.; Inorganica Chimica Acta; vol. 508; (2020);,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

Name is Copper(I) oxide, as a common heterocyclic compound, it belongs to copper-catalyst compound, and cas is 1317-39-1, its synthesis route is as follows.,1317-39-1

3-Chloro-4-nitro-benzonitrile Sodium nitrite (6.78 g in water (40 mL) at 0 C.) was slowly added to a solution of 4-amino-3-chloro-benzonitrile (10.5 g) in water (30 mL) and concentrated hydrochloric acid (30 mL) also at 0 C. After 10 minutes the solution was poured onto a suspension of cuprous oxide (3.48 g) and sodium nitrite (31.69 g) in water (100 mL) at 0 C. The ensuing mixture was stirred at 0 C. for 1 hour then at 23 C. for 1 hour. The resulting mixture was extracted with dichloromethane and the organic layer washed with saturated sodium chloride. The separated organic layer was dried over sodium sulfate and then concentrated to give 3-chloro-4-nitro-benzonitrile (11.31 g).

With the complex challenges of chemical substances, we look forward to future research findings about Copper(I) oxide

Reference£º
Patent; Pfizer Inc.; US2003/78432; (2003); A1;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

Name is Copper(II) acetate, as a common heterocyclic compound, it belongs to copper-catalyst compound, and cas is 142-71-2, its synthesis route is as follows.,142-71-2

General procedure: The reactions of complexing between porphyrins and copper acetate were studied by means of spectrophotometry in the range of 293-318 K. The change in temperature during the experiment did not exceed¡À0.1 K.

With the complex challenges of chemical substances, we look forward to future research findings about Copper(II) acetate

Reference£º
Article; Pukhovskaya; Nam, Dao Tkhe; Fien, Chan Ding; Domanina; Ivanova, Yu. B.; Semeikin; Russian Journal of Physical Chemistry; vol. 91; 9; (2017); p. 1692 – 1702; Zh. Fiz. Khim.; vol. 91; 9; (2017); p. 1508 – 1519,12;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

[1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride, cas is 578743-87-0, it is a common heterocyclic compound, the copper-catalyst compound, its synthesis route is as follows.,578743-87-0

In a glovebox, a 30 mL round-bottom flask was charged with (IPr)CuCl (969.0 mg, 2.00 mmol) and NaOtBu (192.0 mg, 2.00 mmol). Anhydrous THF (12.0 mL) was added. The resulting opaque brown solution was stirred for 2.0 h. It was filtered through Celite in glovebox and concentrated in vacuo affording (IPr)Cu(OtBu) as an off-white powder (802.2 mg, 79% yield).

With the rapid development of chemical substances, we look forward to future research findings about [1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride

Reference£º
Article; Zeng, Wei; Wang, Enyu; Qiu, Rui; Sohail, Muhammad; Wu, Shaoxiang; Chen, Fu-Xue; Journal of Organometallic Chemistry; vol. 743; (2013); p. 44 – 48;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

[1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride, cas is 578743-87-0, it is a common heterocyclic compound, the copper-catalyst compound, its synthesis route is as follows.,578743-87-0

In a dry double-mouth bottle to place Pt – 2 (0.0594 g, 0.1 mmol), CuClNHC (0.0488 g, 0.1 mmol), vacuum pumping and nitrogen cycle three times, then the nitrogen flow by adding 10 ml ethanol, stirring reflux reaction for 4 hours, cooling to room temperature, then added potassium hexafluorophosphate (0.184 g, 1 mmol), stirring at the room temperature reaction 2 hours, filtered, concentrated filtrate, ethanol: dichloromethane=1:10 column, get the orange solid 0.047 g, and the yield is 40%.

With the rapid development of chemical substances, we look forward to future research findings about [1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride

Reference£º
Patent; Jiangsu University Of Science And Technology; Shi Chao; Li Qiuxia; Zhang Xinghua; (24 pag.)CN108690096; (2018); A;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

Copper(II) acetate, cas is 142-71-2, it is a common heterocyclic compound, the copper-catalyst compound, its synthesis route is as follows.,142-71-2

General procedure: Porphyrins 1-6 (Aldrich, 97%), organic solvents (Merck, 99%), and inorganic salts (Acros, 99%) were used as received. The complex formation was studied by recording electronic absorption spectra of the solutions using a Cary 300 spectrophotometer (Varian). To do so,solutions of the studied porphyrin (2.5¡Á10-5 mol/L)and the salt (2.5¡Á10-3 mol/L) in an organic solvent were put in the cell maintained at constant temperature(¡À0.1C), and the absorbance at the wave length corresponding to the maximum in the spectrum of the formed metal porphyrinate was monitored. Kinetic studies of the complex formation were performed over 288-363 K range.

With the rapid development of chemical substances, we look forward to future research findings about Copper(II) acetate

Reference£º
Article; Maltceva; Mamardashvili, N. Zh.; Russian Journal of General Chemistry; vol. 87; 6; (2017); p. 1175 – 1183; Zh. Obshch. Khim.; vol. 87; 6; (2017); p. 955 – 963,8;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

As a common heterocyclic compound, it belong copper-catalyst compound,[1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride,578743-87-0,Molecular formula: C27H36ClCuN2,mainly used in chemical industry, its synthesis route is as follows.,578743-87-0

General procedure: To an oven-dried screwed 20 mL vial were added (NHC)CuCl (c7 or c8, 0.2 mmol) suspended in dry THF (3 mL); in another vial, [tBu3PN]Li (1b, 42.3 mg, 0.95 eq.) was also dissolved in dry THF (3 mL), then the vial was put into glove-box fridge (-35 C) for one hour. Then the cold mixture was dropped into the (NHC)CuCl/THF suspension slowly under stirring and the suspension was turned into clear solution as the lithium salt added. After addition, the reaction mixture was kept at room temperature in glove box for 13 hours. After the reaction was completed, the volatile was removed under vacuum and dry hexane or pentane (7 mL) was added into the formed oily residue. The suspension obtained was kept stirring for another 15 mins at room temperature, then filtered through a short pad of neutral celite to get rid of precipitate. The filtrate was cooled down in the fridge (-35 C) for 3-4 hours to remove the unreacted lithium salt 1b further. Repeated once again to get the clear hexane or pentane filtrate. The filtrate was evaporated until white crystallized solid was formed, which is the catalytic active species (3 or 4). IPrCuCl (c7, 97 mg, 0.2 mmol); Obtain IPrCuNPtBu3 (3, 99 mg, 78%) as Colorless Solid; 1H NMR (C6D6, 600 MHz) delta 7.26-7.21 (br, m, 4H, m-ArH), 7.17-7.14 (br, m, 2H, p-ArH), 6.40 (s, 2H, NCH=), 2.83 (sep, 4H, J = 6.6 Hz, CH(CH3)2), 1.61 (d, 12H, J = 6.6 Hz, CH(CH3)2), 1.37 (d, 27H, J(PH) = 10.8 Hz, P(C(CH3)3)3), 1.20 (d, 12H, J = 6.6 Hz, CH(CH3)2); 13C NMR (C6D6, 151 MHz) delta 146.18, 136.50, 130.42, 128.68, 124.42, 122.05, 40.78, 40.49, 31.01, 29.33, 25.04, 24.42; 31P NMR (C6D6, 243 MHz) delta 26.35 (s); Elemental analysis calcd for [C39H63CuN3P+0.67 THF]: C, 69.84; H, 9.61; N, 5.86. Found: C, 69.48; H, 9.90; N, 6.19.

With the synthetic route has been constantly updated, we look forward to future research findings about [1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride,belong copper-catalyst compound

Reference£º
Article; Bai, Tao; Yang, Yanhui; Han, Chao; Tetrahedron Letters; vol. 58; 15; (2017); p. 1523 – 1527;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

As a common heterocyclic compound, it belong copper-catalyst compound,[1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride,578743-87-0,Molecular formula: C27H36ClCuN2,mainly used in chemical industry, its synthesis route is as follows.,578743-87-0

In a dry double-mouth bottle to place Ir – 1 (0.0695 g, 0.1 mmol), CuClNHC (0.0488 g, 0.1 mmol), vacuum pumping and nitrogen cycle three times, then the nitrogen flow by adding 10 ml ethanol, stirring reflux reaction for 4 hours, cooling to room temperature, then added potassium hexafluorophosphate (0.184 g, 1 mmol), stirring at the room temperature reaction 2 hours, filtered, concentrated filtrate, ethanol: dichloromethane=1:10 column, get the orange solid 0.064 g, and the yield is 50%.

With the synthetic route has been constantly updated, we look forward to future research findings about [1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride,belong copper-catalyst compound

Reference£º
Patent; Jiangsu University Of Science And Technology; Shi Chao; Li Qiuxia; Zhang Xinghua; (24 pag.)CN108690096; (2018); A;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II), cas is 14172-91-9, it is a common heterocyclic compound, the copper-catalyst compound, its synthesis route is as follows.,14172-91-9

(a) N-Bromosuccinimide (0.0131 g, 0.0737 mmol) was added with stirring to a solution of 0.02 g (0.0296 mol) of complex 5 in 10 mL of chloroform and the reaction mixture was heated under reflux for 5 min. The mixture was cooled, water was added, the organic layer was separated, washed with water, dried with Na2SO4, concentrated, chromatographed on aluminum oxide (using hexane, chloroform-hexane 1 : 2, and then chloroform as eluent), and reprecipitated from ethanol. Yield 0.016 g (0.0212 mmol), 72%. (b) N-Bromosuccinimide (0.00788 g, 0.0444 mmol) was added with stirring to a solution of 0.02 g (0.0296 mmol) of complex 5 in a mixture of 10 mL of chloroform and 1 mL of DMF, the reaction mixture was kept at ambient temperature for 35 min. The mixture was treated similarly to method a. Yield 0.017 g (0.0225 mmol), 76%. (c) A mixture of 0.02 g (0.0288 mmol) of porphyrin 2 and 0.052 g (0.288 mmol) of Cu(OAc)2 was dissolved in 10 mL of DMF, the reaction mixture was heated to reflux, cooled, poured into water, solid NaCl was added, the precipitate was separated by filtration, washed with water, dried, and chromatographed on aluminum oxide using chloroform as an eluent. Yield 0.02 g (0.0265 mmol), 85%. MS (m/z (Irel, %)): 754 (56) [M]+; for C44H27N4BrCu calcd.: 755. IR (nu, cm-1): 2926 s, 2855 m nu(C-H, Ph), 1790 w, 1680 w, 1488 s nu(C=C, Ph), 1457 m nu(C=N), 1366 m, 1345 s nu(C-N), 1193 s, 1169 w, 1146 m, 1072 m delta(C-H, Ph), 1005 s nu(C-C), 861 s, 796 s gamma(C-H, pyrrole ring), 749 s, 702 s, 689 m gamma(C-H, Ph). For C44H27N4BrCu anal. calcd. (%): C, 69.98; N,7.42; H, 3.60; Br, 10.58. Found (%): C, 69.72; N, 7.30; H, 3.65; Br 9.67.

With the synthetic route has been constantly updated, we look forward to future research findings about 5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II),belong copper-catalyst compound

Reference£º
Article; Chizhova; Shinkarenko; Zav?yalov; Mamardashvili, N. Zh.; Russian Journal of Inorganic Chemistry; vol. 63; 6; (2018); p. 732 – 735; Zh. Neorg. Khim.; vol. 63; 6; (2018); p. 695 – 699,5;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”