Share a compound : Bis(acetylacetone)copper

13395-16-9 is used more and more widely, we look forward to future research findings about Bis(acetylacetone)copper

Bis(acetylacetone)copper, cas is 13395-16-9, it is a common heterocyclic compound, the copper-catalyst compound, its synthesis route is as follows.

General procedure: In a typical synthesis of Cu40Ag60, 0.45mmol Cu(acac)2 and 0.35 Ag (ac) was mixed with 3mL of OAm, 1 mL of OAc and 11mL of ODE. All synthesis was conducted in a four-necked glass reactor allowing the precise temperature control and inert gas atmosphere under dark conditions. Firstly, the mixture was heated to 60C and kept at this temperature for 10min. Then, the mixture was heated to 180C and kept at this temperature for 30min before it was cooled down to room temperature. After cooling, the resultant reaction mixture was collected with hexane (2mL) and the NPs were separated by centrifugation (8500rpm, 12min) after adding isopropanol (40mL). To further purify the yielded CuAg NPs, the product was centrifuged (8500rpm, 12min) one more time with ethanol (40mL). Finally, the remaining product was dispersed in hexane (10mL) for further use. By using the same recipe and varying metal precursor amounts, two different compositions of CuAg NPs were synthesized. Reductive mixing of 0.3mmol Cu(acac)2 and 0.5 Ag(ac) resulted in Cu30Ag70 NPs and mixing 0.6mmol Cu(acac)2 with 0.4 Ag (ac) led to Cu60Ag40. Synthesis of Ag NPs was conducted with the same recipe without using Cu precursor.

13395-16-9 is used more and more widely, we look forward to future research findings about Bis(acetylacetone)copper

Reference£º
Article; Balkan, Timucin; Kuecuekkececi, Hueseyin; Kaya, Sarp; Metin, Oender; Zarenezhad, Hamaneh; Journal of Alloys and Compounds; vol. 831; (2020);,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

 

Share a compound : 7758-99-8

7758-99-8 is used more and more widely, we look forward to future research findings about Copper(II) sulfate pentahydrate

Copper(II) sulfate pentahydrate, cas is 7758-99-8, it is a common heterocyclic compound, the copper-catalyst compound, its synthesis route is as follows.

Example 2828.1 28.2[0329] Methyl 4-bromo-3-(trifluoromethoxy)benzoate (28.2). To a solution of 4-amino-3-(trifluoromethoxy)benzoic acid (2.00 g, 9.10 mmol) in MeOH (25.0 mL), was slowly added HCl (1.0 mL, 1.0 M in ether) at room temperature. The resulting reaction mixture was stirred at room temperature overnight. Benzene (20 mL) was added, and the reaction was heated at reflux with a Dean-Stark trap to remove the half volume of the solvent. The rest of the solvent was then evaporated to give the product. MS (ESI) m/e = 235.9 [M+l]+, Calc’d for CgHeF3NOs, 235.1. The crude product was used in the next step without further purification. To an ice-cooled suspension of methyl 4-amino-3- (trifluoromethoxy)benzoate hydrogen chloride salt (8.60 g, 31.70 mmol) in 17.1 mL of water and concentrated HBr (48 %, 17.1 mL), was slowly added a prepared 2.5 M solution of sodium nitrite (2.20 g in 12.7 mL) at 00C. The reaction mixture was stirred at 0 0C for 10 minutes. Meanwhile, a solution OfCuSO4 (6.68 g) in 35 mL of water was heated and sodium bromide (6.52 g) was added. The solution became a green color, and a solution OfNa2SOs (2.80 g) in water (10 mL) was then added to it. The solution was cooled at 0 0C and washed with water (25 x 3 mL). The water was then decanted off. Concentrated HBr (16.7 mL) was added, and the solution became a purple color. The solution of CuBr was slowly added to the diazonium salt (prepared above) at 00C. After addition, the ice-bath was removed, and an oil-bath was placed under the reaction vessel. The reaction mixture was then heated to 600C for 15 minutes, at 80 0C for 15 minutes, and then at 1000C for 20 minutes. The reaction mixture was next cooled to room temperature and made basic with Na2CO3 to a pH 8. The aqueous solution was extracted with EtOAc (100 x 2 mL). The organic layer was washed with brine (25 mL) and dried with MgSO4. The solvent was removed to give the crude product 28.2. 1H NMR (CDCl3) delta 3.96 (s, 3H), 7.75 (d, J= 8.4 Hz5 1 H), 7.86 (d, J= 8.4 Hz, 1 H), 7.98 (s, IH).

7758-99-8 is used more and more widely, we look forward to future research findings about Copper(II) sulfate pentahydrate

Reference£º
Patent; AMGEN INC.; WO2008/30520; (2008); A1;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

 

Share a compound : 13395-16-9

13395-16-9 is used more and more widely, we look forward to future research findings about Bis(acetylacetone)copper

Bis(acetylacetone)copper, cas is 13395-16-9, it is a common heterocyclic compound, the copper-catalyst compound, its synthesis route is as follows.

Under a nitrogen atmosphere, copper acetylacetonate (0.9 mmol) was dissolved in 25 mL of dichloromethane, followed by addition of 1,10-phenanthroline (0.9 mmol). The reaction solution was stirred at room temperature for 48 hours and then concentrated in vacuo. The resulting solid was washed with 25 mL of n-pentane and recrystallized with dichloromethane and n-pentane to obtain Catalyst 3. The method of the invention produces this compound in a yield of up to 75%

13395-16-9 is used more and more widely, we look forward to future research findings about Bis(acetylacetone)copper

Reference£º
Patent; Chinese Academy Of Sciences Lanzhou Chemical Physics Institute Suzhou Institute; Li Yuehui; Wang Hua; Dong Yanan; Ke Lisitian¡¤shanduofu; (20 pag.)CN108017557; (2018); A;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

 

Analyzing the synthesis route of 14172-91-9

14172-91-9 5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II) 3722750, acopper-catalyst compound, is more and more widely used in various.

14172-91-9, 5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II) is a copper-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

General procedure: To a solution of corresponding porphyrin, the copper complex(1.13 mmol) in methylene chloride (90 mL) Cu(NO3)2¡¤3H2O(2.30 mmol) in the mixture of acetic acid (5 mL) and acetic anhydride (2 mL) was added, and reaction mixture was stirred for 3 h at room temperature, with TLC monitoring (CHCl3-hexane 1:2). After completion of the reaction the solution was washed with water (200 mL), then with Na2CO3 solution, and the organic phase was separated and dried over Na2SO4. After removal of the solvent under reduced pressure, the residue was purified by column chromatography on silica gel using a CH2Cl2-hexane system (3:7).

14172-91-9 5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II) 3722750, acopper-catalyst compound, is more and more widely used in various.

Reference£º
Article; Ol’shevskaya, Valentina A.; Alpatova, Viktoriya M.; Radchenko, Alexandra S.; Ramonova, Alla A.; Petrova, Albina S.; Tatarskiy, Victor V.; Zaitsev, Andrei V.; Kononova, Elena G.; Ikonnikov, Nikolay S.; Kostyukov, Alexey A.; Egorov, Anton E.; Moisenovich, Mikhail M.; Kuzmin, Vladimir A.; Bragina, Natalya A.; Shtil, Alexander A.; Dyes and Pigments; vol. 171; (2019);,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

 

Brief introduction of 14172-91-9

14172-91-9 5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II) 3722750, acopper-catalyst compound, is more and more widely used in various.

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.14172-91-9,5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II),as a common compound, the synthetic route is as follows.

To a stirred solution of (meso-tetraphenylporphyrinato)copper(II) (1c; 237 mg, 0.35 mmol) inCHCl3 (530 mL) at room temperature, a solution of 25% aqueous nitric acid (freshly prepared fromfuming yellow HNO3, d = 1.52; large excess, 140 mL, 637 mmol) was added dropwise during ca5 min. The reaction mixture was intensively stirred under argon in a round-bottomed ask, protectedagainst light, for 30-40 min with TLC monitoring (CHCl3/n-hexane-1:1). Then, the mixture waspoured into aqueous solution of 5% NaHCO3 (200 mL), and shaken carefully in a separatory funnel.The separated organic layer was washed with water (4 200 mL), and dried with anhydrousMgSO4/Na2CO3. After evaporating the solvent, the residue was subjected to column chromatography(eluent: CHCl3/n-hexane1:1) to give (2-nitro-5,10,15,20-tetraphenylporphyrinato)copper(II) (2c; 71 mg, 28%) and a mixture of dinitro-substituted isomers (150 mg, 56%). Thedinitro-isomers were separated on preparative TLC (CHCl3/n-hexane-1:1, four times developed),allowing isolation of: (a) (2,7-dinitro-5,10,15,20-tetraphenylporphyrinato)copper(II) (3ca; 40 mg,15%); (b) (3,7-dinitro-5,10,15,20-tetraphenylporphyrinato)copper(II) (3cb; 35.5 mg, 13%); (c)(2,8-dinitro-5,10,15,20-tetra-phenylporphyrinato)copper(II) (3cc) contaminated with small amountsof (3,7-dinitro-5,10,15,20-tetraphenylporphyrinato)copper(II) (3cb) (30 mg, yield-ca 10%). 3cc can befurther purified by preparative TLC.

14172-91-9 5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II) 3722750, acopper-catalyst compound, is more and more widely used in various.

Reference£º
Article; Mikus, Agnieszka; Rosa, Mariusz; Ostrowski, Stanis?aw; Molecules; vol. 24; 5; (2019);,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

 

Share a compound : 6046-93-1

With the rapid development of chemical substances, we look forward to future research findings about Copper(II) acetate hydrate

Copper(II) acetate hydrate, cas is 6046-93-1, it is a common heterocyclic compound, the copper-catalyst compound, its synthesis route is as follows.

General procedure: In a 250mL distillation flask, 5,10,15,20-tetraphenylporphyrin (H2TPP) (0.50g, 0.81mmol) and NaOAc (0.30g, 3.6mmol) was stirred in 75mL of chlorobenzene and 50mL of DMF. After the addition of two equivalents of metal acetate, a Soxhlet extractor with a cellulose filter thimble filled with ?3g of K2CO3 was attached to the distillation flask. The assembly was completed with a condenser on the top of the extractor; and then the mixture was heated to reflux at 150C overnight. The reaction extent was monitored by TLC or UV-Vis until all the H2TPP was consumed. After the reaction was compete, the solvent was removed under vacuum. The remaining solid was dissolved in 150mL of chloroform, and washed with water (50mL¡Á3). The organic layer was further washed with a saturated sodium bicarbonate solution (50mL¡Á3), and then dried over K2SO4. After removal of the solvent in vacuo, the solid was recrystallized from chloroform/heptane.

With the rapid development of chemical substances, we look forward to future research findings about Copper(II) acetate hydrate

Reference£º
Article; Yao, Shu A.; Hansen, Christopher B.; Berry, John F.; Polyhedron; vol. 58; (2013); p. 2 – 6;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

 

Share a compound : 6046-93-1

With the rapid development of chemical substances, we look forward to future research findings about Copper(II) acetate hydrate

Copper(II) acetate hydrate, cas is 6046-93-1, it is a common heterocyclic compound, the copper-catalyst compound, its synthesis route is as follows.

meso-Tetraphenylporphyrin (TPP)(2 g, 3.25 mmol) was dissolved in CH2Cl2 (160 mL) and methanol (50 mL). Cu(OAc)2¡¤H2O (1.2 g,5.85 mmol) was added and the mixture was heated to reflux for 2 h until all starting material wasconsumed (TLC, UV-vis). Solvents were evaporated to give a red-purple residue that was filteredthrough a short plug of silica. After filtration, the product 3 was obtained as a dark purple sparklingsolid (2.2 g, 3.25 mmol, 99%)

With the rapid development of chemical substances, we look forward to future research findings about Copper(II) acetate hydrate

Reference£º
Article; Blom, Magnus; Norrehed, Sara; Andersson, Claes-Henrik; Huang, Hao; Light, Mark E.; Bergquist, Jonas; Grennberg, Helena; Gogoll, Adolf; Molecules; vol. 21; 1; (2016);,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

 

Share a compound : Bis(acetylacetone)copper

As the rapid development of chemical substances, we look forward to future research findings about 13395-16-9

Bis(acetylacetone)copper, cas is 13395-16-9, it is a common heterocyclic compound, the copper-catalyst compound, its synthesis route is as follows.

Complex (6) C26H33Cu2N5O14 (FW = 734.66) was prepared by refluxing a hot ethanolic solution of the copper(II) complex (2), (473 mg, 1 mmol) with a hot ethanolic solution of the copper acetyl acetonate (188 mg, 1 mmol). The reaction mixture was refluxed for three hours with stirring. The precipitate so formed, was filtered off, washed with ethanol and dried in vacuum desiccators over CaCl2, Yield 72%, 5.29 gm. Color: Dark brown, m.p. > 300, Elemental Analyses. Calc.: C, 42.51; H, 4.53; N, 9.53; Cu, 15.30; Found: C, 42.21; H, 4.43; N, 9.66; Cu,16.97. IR (KBr, cm-1), 3448(br) nu(H2O), 1685 nu(C=OAcAc), 1670 nu(C=OAcetyl), 1602 nu(C=Nimine), 1570 nu(C=Noxime), 1285 nu(C-OAcAc), 1168 nu(N-O), 670, nu(M-O), 628 nu(M?O), 572 nu(M-N), 510 nu(M?N). Molar conductance (Lambda) is 28.20 Omega-1 cm2 mol-1.

As the rapid development of chemical substances, we look forward to future research findings about 13395-16-9

Reference£º
Article; El-Tabl, Abdou S.; Shakdofa, Mohamad M.E.; Whaba, Mohammed Ahmed; Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy; vol. 136; PC; (2015); p. 1941 – 1949;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

 

Some tips on 14172-91-9

As the paragraph descriping shows that 14172-91-9 is playing an increasingly important role.

14172-91-9, 5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II) is a copper-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

(a) N-Bromosuccinimide (0.105 g, 0.592 mmol) was added with stirring to a solution of 0.02 g (0.0296 mmol) of complex 5 in a mixture of 10 mL of chloroform and 1 mL of DMF, the mixture was stirred at ambient temperature for 8 h. The reaction mixture was concentrated to minimal volume, 10 mL of DMF, water, and solid NaCl were added, the precipitate was separated by filtration, washed with water, acetonitrile, dried, chromatographed on aluminum oxide using chloroform as an eluent, and reprecipitated from ethanol. Yield 0.026 g (0.0199 mmol), 68%. MS (m/z (Irel, %)): 1306.6 (98) [M]+; for C44H20N4Br8Cu calcd.: 1307.5. IR (nu, cm-1): 2925 s, 2853 m nu(C-H, Ph), 1680 w, 1488 m nu(C=C, Ph), 1467 w, 1444 w nu(C=N), 1366 w, 1351 w nu(C-N), 1175 m, 1145 w, 1108 w delta(C-H, Ph), 1024 s nu(C-C), 924 m, 858 m gamma(C-H, pyrrole ring), 756 m, 734 m, 695 m gamma(C-H, Ph). For C44H20N4Br8Cu anal. calcd. (%): C, 40.42; N, 4.29; H, 1.54; Br, 48.89. Found (%): C, 40.15; N, 4.16; H, 1.59; Br, 48.71.

As the paragraph descriping shows that 14172-91-9 is playing an increasingly important role.

Reference£º
Article; Chizhova; Shinkarenko; Zav?yalov; Mamardashvili, N. Zh.; Russian Journal of Inorganic Chemistry; vol. 63; 6; (2018); p. 732 – 735; Zh. Neorg. Khim.; vol. 63; 6; (2018); p. 695 – 699,5;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”