Category: 7787-70-4

Each compound has different characteristics, and only by selecting the characteristics of the compound suitable for a specific situation can the compound be applied on a large scale. 7787-70-4, name is Copper(I) bromide. This compound has unique chemical properties. The synthetic route is as follows. 7787-70-4

General procedure: The complexes were typically obtained from the reaction of the copper halide (CuX) with the appropriate camphor ligand in THF (3 mL) upon stirring for ca. 18 h at room temperature. Filtration of the precipitate, washing with n-pentane (ca. 6mL) and drying under vacuum affords the Cu(I) complex.

As the rapid development of chemical substances, we look forward to future research findings about 7787-70-4

Reference£º
Article; Fernandes, Tiago A.; Mendes, Filipa; Roseiro, Alexandra P.S.; Santos, Isabel; Carvalho, M. Fernanda N.N.; Polyhedron; vol. 87; (2015); p. 215 – 219;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact.7787-70-4, Copper(I) bromide it is a common compound, a new synthetic route is introduced below.7787-70-4

7787-70-4, General procedure: To a solution of (S,S)-iPr-pheboxH (0.051g, 0.173mmol) in dichloromethane (15mL), the corresponding copper(I) salt CuX (X=Cl, Br, I) (0.347mmol) was added and the mixture stirred at room temperature during 24h. Then, the reaction mixture was filtered via cannula, concentrated under reduced pressure to ca. 2mL and diethyl ether/n-hexane (1:2) (30mL) was added. The resulting solid was washed with n-hexane (3¡Á5mL) and vacuum-dried.

As the paragraph descriping shows that 7787-70-4 is playing an increasingly important role.

Reference£º
Article; Vega, Esmeralda; De Julian, Eire; Borrajo, Gustavo; Diez, Josefina; Lastra, Elena; Gamasa, M. Pilar; Polyhedron; vol. 94; (2015); p. 59 – 66;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

7787-70-4, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route., 7787-70-4

To a solution of CuBr (0.0135 g, 0.094 mmol) in 10 mL of acetonitrile was added dropwise 1 (0.03 g, 0.094 mmol) in dichloromethane (5 mL) at room temperature. The reaction mixture was stirred for 4 h. The solvent was removed under reduced pressure to get 6 as a pale yellow solid. Analtyically pure product of 6 was obtained by recrystallizing the crude product in a 1:2 mixture of dichloromethane and petroleum ether. Yield: 81% (0.035 g). Mp: 158-160 C. Anal. Calc. for C42H44Cu2Br2N2P2: C, 54.66; H, 4.80; N, 3.03. Found: C, 54.95; H, 4.85; N, 2.88%. 1H NMR (400 MHz, CDCl3): delta 7.52-6.83 (m, Ar, 28H), 3.50 (s, CH2, 4H), 2.42 (s, NMe2, 12H). 31P{1H} NMR (162 MHz, CDCl3): delta -16.2 (br s). MS (EI): m/z 845.22 [M-Br]+.

As the paragraph descriping shows that 7787-70-4 is playing an increasingly important role.

Reference£º
Article; Ananthnag, Guddekoppa S.; Edukondalu, Namepalli; Mague, Joel T.; Balakrishna, Maravanji S.; Polyhedron; vol. 62; (2013); p. 203 – 207;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact.7787-70-4, Copper(I) bromide it is a common compound, a new synthetic route is introduced below.7787-70-4

Copper bromide (0.079 g, 0.55 mmol) was added to 30 mL of ppdq (0.200 g, 0.55 mmol) In a solution of CH2Cl2, the mixture was stirred at room temperature to form a red suspension, the reaction mixture was filtered, and the solvent was removed under reduced pressure. A red powder was obtained which was recrystallized from CH2Cl2 to give red crystals: 0.238 g, 85.3%.

With the synthetic route has been constantly updated, we look forward to future research findings about Copper(I) bromide,belong copper-catalyst compound

Reference£º
Patent; Hubei University; Liu Li; Guo Bangke; (13 pag.)CN109970769; (2019); A;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

7787-70-4, Copper(I) bromide is a copper-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

7787-70-4, General procedure: The complexes were prepared according to the following method [14]: 1mmol of copper(I) bromide or copper(I) chloride is stirred in methanol until complete dissolution. Then, 2.1 mmol of the corresponding phosphine ligand was added. The mixture was stirred at 60C for 30min. under nitrogen atmosphere. A microcrystalline precipitate was obtained by concentration of the solution at reduced pressure. The solid product was dissolved in a dichloromethane/methanol mixture and the solution was gradually cooled to 4C to give an air stable and colorless crystalline solid suitable for X-ray single-crystal diffraction studies.

7787-70-4 Copper(I) bromide 24593, acopper-catalyst compound, is more and more widely used in various fields.

Reference£º
Article; Espinoza, Sully; Arce, Pablo; San-Martn, Enrique; Lemus, Luis; Costamagna, Juan; Faras, Liliana; Rossi, Miriam; Caruso, Francesco; Guerrero, Juan; Polyhedron; vol. 85; (2015); p. 405 – 411;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

As we all know, there are many different methods for the synthesis of a compound, and people can choose the synthesis method that suits their own laboratory according to the actual situation. 7787-70-4, Copper(I) bromide. This compound is widely used in many fields, so it is necessary to find a new synthetic route. The downstream synthesis method of this compound is introduced below.7787-70-4

Compound 2 (23mg, 0.05mmol) in dichloromethane (2mL) was slowly added on a solution of copper bromide (7.2mg, 0.05mmol) in acetonitrile (2mL) at-60C. The orange-red solution resulting from complete diffusion was slowly evaporated at r.t. to afford compound 6 (quantitative yield) as colorless crystals suitable for an X-ray diffraction analysis. Mp=93C. 1H NMR (CDCl3, 300MHz): delta 5.21 (s, 4H, =CH2), 4.30-3.95 (m, 8H, CH2-C=), 4.00-2.35 (m, 24H). Br2C20Cu2H36O4S4 (755.56): calcd C 31.79, H, 4.80; found: C 31.09, H, 4.22.

With the rapid development of chemical substances, we look forward to future research findings about 7787-70-4

Reference£º
Article; Carel, Guillaume; Madec, David; Saponar, Alina; Saffon, Nathalie; Nemes, Gabriela; Rima, Ghassoub; Castel, Annie; Journal of Organometallic Chemistry; vol. 755; (2014); p. 72 – 77;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

Copper(I) bromide, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route. 7787-70-4

Copper bromide (0.079 g, 0.55 mmol) was added to 30 mL of ppdq (0.200 g, 0.55 mmol) In a solution of CH2Cl2, the mixture was stirred at room temperature to form a red suspension, the reaction mixture was filtered, and the solvent was removed under reduced pressure. A red powder was obtained which was recrystallized from CH2Cl2 to give red crystals: 0.238 g, 85.3%.

As the paragraph descriping shows that 7787-70-4 is playing an increasingly important role.

Reference£º
Patent; Hubei University; Liu Li; Guo Bangke; (13 pag.)CN109970769; (2019); A;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

7787-70-4, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route., 7787-70-4

The ligand (50.0 mg, 0.11 mmol) was added to a suspension of copper(II) halogenide (0.11 mmol) in methanol (3 ml). The mixture was stirred at r. t. for 16 h. The precipitate was then filtered off and dried in vacuo. The pure compounds were obtained by recrystallization from dichloromethane and pentane.

With the rapid development of chemical substances, we look forward to future research findings about Copper(I) bromide

Reference£º
Article; Sauer, Desiree C.; Wadepohl, Hubert; Polyhedron; vol. 81; (2014); p. 180 – 187;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact.7787-70-4, Copper(I) bromide it is a common compound, a new synthetic route is introduced below.7787-70-4

a. 2-(carboxy-5-nitro-phenyl)malonic acid dimethyl ester (2) A solution of 2-chloro-4-nitrobenzoic acid (75 g, 372 mmol) in dimethyl malonate (900 mL) was sparged with nitrogen for 15 min. Sodium methoxide (48.3 g, 894 mmol) was added in one portion and the contents exothermed to 480 C. Fifteen minutes later, copper (I) bromide (5.4 g, 37 mmol) was added in one portion and the contents heated to 70 C. for 24 hrs. The reaction was 70% complete by nmr, the contents heated to 85 C. for 6 hrs to completely consume the 2-chloro-4-nitrobenzoic. Water (900 mL) was added to the cooled reaction followed by hexanes (900 mL). The aqueous layer was separated, toluene (900 mL) added, filtered through celite, and aqueous layer separated. Fresh toluene (1800 mL) was added to the aqueous layer and the biphasic mixture acidified with 6N aqueous HCl (90 mL). A white precipitate formed and the contents stirred for 18 hrs. The product was filtered off and dried to give a white soid (78.1 g, 70%) mp=153 C. 1 H NMR (CD3)2 SO delta 78.37 (d, J=2 Hz, 1H), 8.30 (d, J=1 Hz, 2H), 5.82 (s, 1H), (3.83 (s, 6H). 13 C NMR (CD3)2 SO delta 168.0, 167.3, 149.4, 137.1, 135.8, 132.5, 125.4, 123.7, 54.5, 53.4. Anal. Calcd for C11 H10 NO8: C, 48.49; H, 3.73; N, 4.71. Found: C, 48.27; H. 3.72; N, 4.76.

With the synthetic route has been constantly updated, we look forward to future research findings about Copper(I) bromide,belong copper-catalyst compound

Reference£º
Patent; Pfizer INc.; US5919795; (1999); A;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

Copper(I) bromide, A common heterocyclic compound, its traditional synthetic route has been very mature, but the traditional synthetic route has various shortcomings, such as complicated route, low yield, poor purity, etc., below Introduce a new synthetic route. 7787-70-4

General procedure: The complexes were prepared according to the following method [14]: 1mmol of copper(I) bromide or copper(I) chloride is stirred in methanol until complete dissolution. Then, 2.1mmol of the corresponding phosphine ligand was added. The mixture was stirred at 60C for 30min. under nitrogen atmosphere. A microcrystalline precipitate was obtained by concentration of the solution at reduced pressure. The solid product was dissolved in a dichloromethane/methanol mixture and the solution was gradually cooled to 4C to give an air stable and colorless crystalline solid suitable for X-ray single-crystal diffraction studies.

7787-70-4 Copper(I) bromide 24593, acopper-catalyst compound, is more and more widely used in various fields.

Reference£º
Article; Espinoza, Sully; Arce, Pablo; San-Martin, Enrique; Lemus, Luis; Costamagna, Juan; Farias, Liliana; Rossi, Miriam; Caruso, Francesco; Guerrero, Juan; Polyhedron; vol. 85; (2014); p. 405 – 411;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”