Category: copper-catalyst

As a common heterocyclic compound, it belongs to copper-catalyst compound, name is Bis(acetylacetone)copper, and cas is 13395-16-9, its synthesis route is as follows.,13395-16-9

A yellow solution of H4L (0.3mmol, 0.068g) in MeOH (5mL) was added to a green solution of Cu(acac)2 (0.30mmol, 0.079g) in dmf (20mL) which was stirred under heating at ~90C. The resulting dark green solution was refluxed for 3h and after cooled at r.t. was layered with Et2O. X-ray quality blue crystals of 1¡¤MeOH were formed after 3weeks. The identity of the crystals was confirmed by unit cell determination (a=b=17.414(1), c=16.751(1) A, alpha=beta=gamma=90, V=5079A3). The crystals were filtered off and dried under vacuum. (Yield: 0.056g, ?65%). The solid was analyzed as solvent free. C44H52Cu4N4O16 requires: C, 46.07; H, 4.57; N, 4.88. Found: C, 45.88; H, 4.54; N, 4.85%. FT-IR (KBr pellets, cm-1): 3413(br,s), 2912(w), 2873(w), 2828(w), 1625(vs), 1603(s), 1543(s), 1473(s), 1448(s), 1399(m), 1385(m), 1338(m), 1300(vs), 1254(m), 1206(m), 1160(m), 1129(m), 1083(m), 1029(s), 980(w), 936(w), 915(m), 875(m), 770(s), 683(s), 633(m), 586(m), 489(m), 454(m).

With the complex challenges of chemical substances, we look forward to future research findings about 13395-16-9,belong copper-catalyst compound

Reference£º
Article; Lazarou, Katerina N.; Savvidou, Aikaterini; Raptopoulou, Catherine P.; Psycharis, Vassilis; Polyhedron; vol. 152; (2018); p. 125 – 137;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

As a common heterocyclic compound, it belongs to copper-catalyst compound, name is Copper(II) sulfate pentahydrate, and cas is 7758-99-8, its synthesis route is as follows.,7758-99-8

18 g of copper sulphate and 6.75 g of sodium bromide were added to 150 ML of D. M water in a 3 necked round bottom flask. The contents of flask were heated to 76-78 C to obtain a clear solution. 6g of sodium metabisulphite was then added to it in portions and stirred for 15 min. The reaction mixture was cooled to 30 2 C. CuBr solid was filtered. To 150 g of compound of formula 2 was added 1.5 1 of acetone and 600 ml of methanol. The contents of the flask were cooled to 18-20 C. 245 ml of aqueous HBR was added to the above reaction mixture at 18-20 C in a single charge. Cool the contents of the flask to 0-2 C. 120ML of 50% w/v aqueous sodium nitrite solution was added slowly to the reaction mixture by maintaining the temperature between 0-2 C, over a period of 30 minutes. The reaction mixture was maintained for 15 minutes at 0-2 C. The temperature was raised to 20-22 C. A solution of 246g of acrylamide in 900ML of acetone was added at 22-23 C in single charge. The reaction mixture was stirred for 10 minutes at 23-24 C, 4. 6g of cuprous bromide was added in a single charge under vigorous stirring and the reaction mixture maintained for 2 hours at 30-35 C. After completion of the reaction, acetone and methanol were. distilled off completely to obtain thick liquid mass. A solution of 150 g of sodium bicarbonate in 3.0 1 of D. M water was prepared. 600ML of hexane was added to it and stirred to get a clear biphasic solution. The reaction mixture was gradually quenched into above flask containing aqueous sodium bicarbonate and hexane solution over a period of 30 minutes at 23-35 C followed by stirring for 2 hours. The product was filtered and the product cake washed with D. M. Water followed by hexane and dried. The crude product obtained was suspended in water and stirred for 1 hour at 25-30 C. The product was filtered and cake washed with D. M. Water followed by hexane. The product thus obtained was suspended in hexane and stirred for 2 hours at 35- 40C. It was filtered and washed with hexane and dried to get compound of formula 3.

With the complex challenges of chemical substances, we look forward to future research findings about 7758-99-8,belong copper-catalyst compound

Reference£º
Patent; SUN PHARMACEUTICAL INDUSTRIES LIMITED; WO2004/108721; (2004); A1;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

As a common heterocyclic compound, it belongs to copper-catalyst compound, name is Cuprouschloride, and cas is 7758-89-6, its synthesis route is as follows.,7758-89-6

EXAMPLE 1 N2-(4-Bromophenyl)-5-trifluoromethyl-1,3-benzoxazol-2-amine 4-Bromophenyl isothiocyanate (1.667 g, 7.785 mmol) was added to a solution of 2-amino-4-trifluoromethylphenol (1.379 g, 7.785 mmol) in tetrahydrofuran (THF) (100 mL) and the reaction was stirred at room temperature for about 16 hours then at about 50 C. for about another 5 hours. Copper (I) chloride (0.771 g, 7.785 mmol) and triethylamine (1.08 mL, 7.785 mmol) were added, and the mixture was stirred at room temperature for about 72 hours and then at about 50 C. for about another 18 hours. Additional copper (I) chloride (0.385 g) was added and the reaction was stirred at about 60 C. for about another 2 hours. The reaction was concentrated under reduced pressure, dissolved in methanol (200 mL), filtered through a pad of diatomaceous earth and the solvent removed in vacuo to afford N2-(4-bromophenyl)-5-trifluoromethyl-1,3-benzoxazol-2-amine as a brown solid (3.90 g, 140% of theory); RP-HPLC Rt 17.627 min, 77% purity (5% to 85% acetonitrile/0.1M aqueous ammonium acetate, buffered to pH 4.5, over 20 min at 1 mL/min; lambda=254 nm; Waters Deltapak C18, 300 A, 5 mum, 150*3.9 mm column); and m/z 354.9 and 356.9 (M-H)-.

With the complex challenges of chemical substances, we look forward to future research findings about 7758-89-6,belong copper-catalyst compound

Reference£º
Patent; Wishart, Neil; Rudolph, Alena; Ritter, Kurt; US2003/109714; (2003); A1;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

As a common heterocyclic compound, it belongs to quinuclidine compound,Quinuclidine-4-carboxylic acid hydrochloride,40117-63-3,Molecular formula: C8H14ClNO133,mainly used in chemical industry, its synthesis route is as follows.,14172-91-9

General procedure: Under the protection of nitrogen, 0.14 mmol of the corresponding 5,10,15,20-tetrakis(4-R-phenyl)porphyrin copper(II)complex was dissolved in 16 ml of CHCl3, to which 0.75 ml of DMFwas added with magnetic stirring. The solution was cooled to 0 Cin an ice bath, and then 0.56 ml of phosphoryl chloride (POCl3) wasslowly added within 20 min. The ice bath was removed and stirringwas continued at room temperature for 1 h, and the solution wascontinuously stirred and heated at 70 C for 24 h. Then 3.606 g ofNaAc and 14.4 ml of distilled water were added in an ice bath andstirring for another 1 h. After separation of the aqueous layer, theorganic layer was washed with 10 ml of distilled water for 3 times,then dried over anhydrous magnesium sulfate and filtered. Thesolvent was removed by rotary evaporation at low temperature toafford a crude product. The crude product was dissolved indichloromethane and subjected to column chromatography overneutral alumina with dichloromethane/petroleum ether (v/v 3:1)as the eluent. The third coloured bandwas collected and the solventwas removed by rotary evaporation to afford a purple powder.

With the complex challenges of chemical substances, we look forward to future research findings about 5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II),belong copper-catalyst compound

Reference£º
Article; Wu, Zhen-Yi; Yang, Sheng-Yan; Journal of Molecular Structure; vol. 1188; (2019); p. 244 – 254;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.578743-87-0,[1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride,as a common compound, the synthetic route is as follows.,578743-87-0

Chloro[l ,3-bis(2,6-di-i-propylphenyl)imidazol-2-ylidene]copper(I) (121.9 mg, 0.25 mmol) and silver triflate (64.2 mg, 0.25 mmol) were mixed under nitrogen in 25 mL flask and 10 mL of dry THF were added. Reaction mixture was stirred at RT for 30 minutes. Solution of 1 , 10-phenanthroline (45.05 mg, 0.25 mmol) in dry THF (5 mL) was added. Reaction mixture turned yellow and was stirred at RT overnight. Resulting mixture was filtered through Celite and solvent was evaporated on rotovap. Recrystallization from CH2Ch by vapor diffusion of Et20 gave 120 mg (61.4%) of yellow crystals. Anal, calcd. for C40H44CUF3N4O3S: C, 61.48; H, 5.68; N, 7.17; Found: C, 61.06; H, 5.61; N, 7.14. Structure was confirmed by IH-NMR spectrum of [(IPR)Cu(phen)]OTf (CDCb, 400MHz).

The synthetic route of 578743-87-0 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; THE UNIVERSITY OF SOUTHERN CALIFORNIA; THOMPSON, Mark; DJUROVICH, Peter; KRYLOVA, Valentina; WO2011/63083; (2011); A1;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.578743-87-0,[1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride,as a common compound, the synthetic route is as follows.,578743-87-0

Carbazole (83.6mg, 0.5mmol) and NaH (12 mg, 0.5 mmol) was mixed with THF and 15 ml, atroom temperature under a nitrogen atmosphere until bubbling ceased (15 min) and stirred.Chloro [1,3-bis (2,6-diisopropylphenyl) imidazol-2-ylidene] was added copper (I) ((IPr) CuCl)(243.8mg, 0.5mmol), the reaction mixture was stirred for one hour did. Then, the mixture wasfiltered through a plug of Celite (registered trademark) under an inert atmosphere, and thesolvent was removed by rotary evaporation. The product was obtained as a white solid (170mg,55%).

The synthetic route of 578743-87-0 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; Universal Display Corporation; Mark, E. Thomson; Peter, I. Jurobitchi; Valentina, Krirowa; (66 pag.)JP2015/91800; (2015); A;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

As a common heterocyclic compound, it belongs to copper-catalyst compound, name is 5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II), and cas is 14172-91-9, its synthesis route is as follows.,14172-91-9

Cu(II)TPP (3) (0.7 g, 1.0 mmol)was dissolved in chloroform (700 mL) and acetic acid (15 mL) was added. Cu(NO3)2¡¤3H2O (0.63 g,2.6 mmol) was dissolved in acetic anhydride (70 mL) and added to the reaction mixture. The mixturewas heated to 35 C and let to stir for 5 h. The reaction mixture was washed with water(3 ¡Á 700 mL), saturated K2CO3 solution (2 ¡Á 700 mL) and again with water (2 ¡Á 700 mL), dried overanhydrous Na2SO4 and solvents removed by azeotropic evaporation with methanol. The residue waspurified by column chromatography using CH2Cl2:pentane 1:1 as eluent resulting in Cu(II)TPPNO2(4) as a dark purple solid (0.65 g, 0.89 mmol, 89%)

14172-91-9 is used more and more widely, we look forward to future research findings about 5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II)

Reference£º
Article; Blom, Magnus; Norrehed, Sara; Andersson, Claes-Henrik; Huang, Hao; Light, Mark E.; Bergquist, Jonas; Grennberg, Helena; Gogoll, Adolf; Molecules; vol. 21; 1; (2016);,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

[1,3-Bis(2,6-diisopropylphenyl)imidazol-2-ylidene]copper chloride, cas is 578743-87-0, it is a common heterocyclic compound, the copper-catalyst compound, its synthesis route is as follows.,578743-87-0

Carbazole (83.6mg, 0.5mmol) and NaH (12 mg, 0.5 mmol) was mixed with THF and 15 ml, atroom temperature under a nitrogen atmosphere until bubbling ceased (15 min) and stirred.Chloro [1,3-bis (2,6-diisopropylphenyl) imidazol-2-ylidene] was added copper (I) ((IPr) CuCl)(243.8mg, 0.5mmol), the reaction mixture was stirred for one hour did. Then, the mixture wasfiltered through a plug of Celite (registered trademark) under an inert atmosphere, and thesolvent was removed by rotary evaporation. The product was obtained as a white solid (170mg,55%).

As the rapid development of chemical substances, we look forward to future research findings about 578743-87-0

Reference£º
Patent; Universal Display Corporation; Mark, E. Thomson; Peter, I. Jurobitchi; Valentina, Krirowa; (66 pag.)JP2015/91800; (2015); A;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.14172-91-9,5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II),as a common compound, the synthetic route is as follows.,14172-91-9

0.0157 g (0.088 mmol) of N-bromosuccinimide was added to a solution of 0.04 g (0.059 mmol) of Cuin 20 mL of l3, and the mixture was refluxed during 30 min. The operation was repeated three times,total amount of the added N-bromosuccinimide being0.047 g (0.26 mmol). After addition of the last portion of the reactant, the mixture was refluxed during 2 hand cooled to ambient; a solution of 0.07 g (0.44 mmol)of bromine in 5 mL of CHCl3 was then added atstirring. The resulting mixture was kept at 20 during about 24 h. Excess of bromine was removed by washing the reaction mixture with 15 mL of 20%aqueous solution of Na2S2O3. The organic layer was washed with water and dried over Na2SO4. The solvent was removed, and the residue was purified by chromatographyon alumina eluting with chloroform,followed by recrystallization from ethanol. Yield 0.055 g(72%, 0.0421 mmol).

14172-91-9 5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II) 3722750, acopper-catalyst compound, is more and more widely used in various.

Reference£º
Article; Maltseva; Zvezdina; Chizhova; Mamardashvili, N. Zh.; Russian Journal of General Chemistry; vol. 86; 1; (2016); p. 102 – 109; Zh. Obshch. Khim.; vol. 86; 1; (2016); p. 110 – 117,8;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”

14172-91-9, 5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II) is a copper-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated,14172-91-9

The copper tetraphenyl porphyrinssynthesised as above was converted into itsoctabromo derivative by the addition of liquidbromine (1.2ml)in chloroform(50ml) to a solution ofCu(TPP)(0.50g) in chloroform:carbon tetrachloride(1:1 V/V) (500ml) in a conical flask. Bromine wasadded dropwise and slowly over a period of halfhour, at room temperature. The contents were stirredfor 4hours, followed by addition of pyridine 2.4mlin 40ml mixture of CHCl3:CCl4in 1:1 ratio. Theaddition took about half hour and stirring continuedfor 12hours. The bromination process wasmonitored by UV-visible spectroscopy to ensurecomplete bromination. The excess bromine was destroyed byaddition of sodium metasulphite (200ml 20% aq.solution) to the system. The organic layer wasseparated using a separating funnel and the solutionwas dried over anhydrous sodium sulphate. Theevaporation of solvent under reduced pressureresulted a green solid of copper octabromoteraphenylporphyrin [Cu(OBTPP)]. The solid was dissolved inminimum amount of chloroform and columnchromatography was done. The first fraction comingout of the column was collected. The removal of solventyielded copper octabromotetraphenyl porphyrin(3)in purified form, yield (75%).

14172-91-9 5,10,15,20-Tetraphenyl-21H,23H-porphine copper(II) 3722750, acopper-catalyst compound, is more and more widely used in various.

Reference£º
Article; Raikwar, Kalpana; Oriental Journal of Chemistry; vol. 31; 2; (2015); p. 1195 – 1200;,
Copper catalysis in organic synthesis – NCBI
Special Issue “Fundamentals and Applications of Copper-Based Catalysts”